Hypertech Max Energy, Max Energy E-Cons Programmers & Speedometer Calibrators


hyp-prgmrMax Energy Tuners are the

The Best Handheld Performance Tuner On The Market!

Max Energy Tuning extracts every bit of energy possible out of every molecule of fuel giving you more miles at part-throttle and more power at wide-open throttle. The results are maximum power and fuel mileage. These programmers are even Internet updateable with the included USB cable. Available for  gas or diesel vehicles.


Additional features (depending on the vehicle application) include:

  • Power tuning
  • Raise the top-speed limiter to match the speed rating of high performance tires
  • Raise the engine’s rpm limiter for increased performance
  • Adjust individual automatic transmission shift points and shift firmness
  • Recalibrate speedometer and odometer for non-stock tire sizes and/or gear ratio changes
  • Lower the cooling fan on/off temperatures to match the thermostat rating
  • Read and clear diagnostic trouble codes and turn off “check engine” lights
  • Active Fuel Management
  • 0-60 Throttle Restriction
  • Ability to adjust settings or go back to stock calibration at any time
  • Internet Updateable

GM Applications: P/N 32500  & P/N 32501

Ford/Lincoln/Mercury Applications: P/N 42002, P/N 42500 & P/N 42501

Chrysler/Dodge/Jeep/ Mitsubishi Applications: P/N 52500, P/N 52501, P/N 52502 & P/N 52503


Designed for the driver who needs better fuel mileage and more power, but who doesn’t want to pay for other high-performance features they may not need.

Every E-CON is programmed with Hypertech’s Max Energy™ Tuning, the best optimized fuel tuning programs possible that increase horsepower and torque. Hypertech’s customers are claiming 2 to 6 mpg gains and a substantial increase in horsepower and torque.


  • Engine Tuning
  • Read & Clear Diagnostic Trouble Codes (DTCs)
  • Return To Stock Or Change Option Settings
  • Internet Updateable

GM Applications: P/N 33500 &  P/N 32501

Ford/Lincoln/Mercury Applications: P/N 43002, P/N 43500 & P/N 43501

Chrysler/Dodge/Jeep/ Mitsubishi Applications: P/N 53500, P/N 53501, P/N 53502 & P/N 53503


Designed  for the drivers who want the speedometer recalibration functions of the Max Energy Programmer without the additional expense of the other tuning features.

Simply plug Hypertech’s Speedometer Calibrator into the vehicle’s under-dash connector, select the new tire height and/or new rear gear ratio, and in a matter of minutes, the vehicle’s computer is reprogrammed for accurate readings (as required by law).

The Speedometer Calibrator comes with a USB cable and a CD containing software to enable quick updates and upgrades over the internet.

GM Applications: P/N 732500 & P/N 732501

Ford/Lincoln/Mercury Applications: P/N 742002,  P/N 742500 & P/N 742501

Chrysler/Dodge/Jeep/ Mitsubishi Applications: P/N 752500, P/N 752501, P/N 752502 &  P/N 752503


The  in-line module corrects the speedometer and odometer for non-stock tire sizes and/or rear gear ratios.

It is perfect for vehicles with computers that don’t allow for tire size and/or rear gear ratio correction or re-calibrate for tire sizes and/or rear gear ratios outside the range of programmers. There are no limitations for increasing tire height or rear gear ratios.

In a matter of minutes, you can accurately correct your speedometer and odometer readings (as required by law).

Installation is a snap! Use the USB cable to connect the In-line Speedometer Calibrator Module to your PC and enter the new tire height and/or rear gear ratio.  Then disconnect the factory connector to the instrument cluster (behind the dash) and  snap in the Speedometer Calibrator Module and reconnect the cluster. You’re done!

In a matter of minutes, you can accurately correct your speedometer and odometer readings (as required by law).

GM Applications: P/N 730100, P/N 730101 &  P/N 730102

Ford Applications: P/N 730110, P/N 730111 & P/N 730112

Toyota Applications: P/N 730103,  P/N 730107,  P/N 730108  & P/N 730113 & P/N 730114

Nissan Applications: P/N 730104,  P/N 730105 &  P/N 730106

Please go to http://www.hypertech.com/Default.aspx to find the specific part number for your application.

This entry was posted in Featured, What's New. Bookmark the permalink.